Y-Block Ford Alternator Mounting Brackets
We now offer a quality engineered alternator-mounting bracket for the Y-Block Ford V8 Engine. These alternator brackets allow our 89 / 90 series alternators to be mounted in the same position as the original Ford Y-Block generator, using the original fan belt and the same belt adjustment procedure as before. Mounting hardware is included.

Applications
1954 thru 1964 Ford Truck V8 -
Part # 03415YT - $85.00 each
1954 thru 1962 Ford Car V8 -
Part # 03415YC - $85.00 each

The 1955 thru 1957 Ford T-Bird V8 applications require a special alternator bracket kit that also includes a special pulley for the 89/90 series alternator. This alterator bracket kit includes everything you need to install our 89 / 90 series alternators on your 1955 thru 1957 Ford T-Bird application.

Application
1955 through 1957 T-Bird only - PT # 03415YTB - $105.00 each

2N/9N/8N Ford Tractor Alternator
Mounting Brackets
Allows you to install the 89/90 series alternator on your Ford 2N/9N/8N series tractor. Brackets are available for both left and right side alternator mounting. (Note: Ford moved the generator to the left side of engine in late 1949 when the distributor was moved from lower front of engine to the upper right side of engine.
Right Side – Part #04415ET-$65.00 each
Left Side – Part #04415LT-$65.00 each

Universal Mounting Bracket
Fits nearly all applications not covered by our custom bracket selection. Mounts to original generator bracket or can be used as a stand alone bracket. hardware package included.
Part #90502UB-$65.00 each

Heavy Duty Wire-Wound Heater Blower Motor Voltage Reducer
Allows the original 6-volt heater blower motor and control switch to be used when electrical system is upgraded to 12-volts. Safer and much more reliable than the less expensive ceramic type voltage reducers.
Part #02415HR-$18.00 each
Installation Instructions

Heavy Duty Headlight Relays
Available for both 6 and 12-volt applications. Installing a headlight relay will provide up to 30 percent brighter headlights and a 50 percent longer service life for the original headlight switch.
6-volt Relay – Part #03415HL6-$27.00
12-volt Relay – Part #03415HL12-$22.00
Installation Instructions

Solid State Generator Cutout
Direct replacement for all 6/12-volt 35-amp and smaller generators that originally had a mechanical, cutout type voltage regulator. No mechanical points to adjust or wear out. No more battery drain. Greatly improves charging system reliability.
Part #02415SSC-$45.00 each

Regulated 12-volt Negative Ground
Power Inverter
Allows you to run modern solidstate accessories from you 6-volt alternator charging system. Great for recharging a cell phone, and providing power to modern solidstate accessories. Five-amp constant regulated output. Use with negative ground accessories only.
Part #02415PI-$99.00 each

“DA” Plugs
For adapting alternator to original wiring harness and will work with both 6 and 12 volt applications.
$18.00 each
Installation Instructions

Runtz Voltage Drops
For dash gauges—one required per electrical gauge.
Part #95415G-$18.00 each
Installation Instructions

Internal Resisted Coil
Increase the reliability of your ignition system while liminating the external ballast resistor, a known trouble spot. Will replace all 6/12 volt external mounted ignition coils. Will also work with electronic ignition conversion.
6-volt-Part #954156C-$70.00 each
12-volt-Part #9541512C-$70.00 each

Ford Coil Adapter
Allows the use of a modern 6 or 12-volt Internal resisted ignition coil with early front mount Ford/Mercury V8 distributors. Gets the coil up away from engine heat and radiator coolant overflow for increased reliability of the ignition system.
1933-1936 3-screw V8 distributors – Part #02415ECA-$47.00 each
1937-1941 2-screw V8 distributors – Part #02415LCA-$47.00 each